DIY Network

All Projects

TV Projects

    What Do You Want To Work On?

      What Activity Do You Want To Do?

        0

        Available Projects

        Get Results

        DIY Network /

        Message Boards

            DIY Message Boards  Hop To Forum Categories  Home Improvement  Hop To Forums  General Home Improvement    Water Softener Discharging into a Sump Pump
        Go
        New
        Find
        Notify
        Tools
        Reply
          
        Water Softener Discharging into a Sump Pump Sign In/Join 
        posted
        Hi All,

        First post here, but always enjoyed reading and learning from many of the experts on this board.

        I recently purchased the Kenmore Elite Hybrid Water Softener and had it installed yesterday. I had a certified plumber in to do the work, and after searching through the basement (which is finished), the only spot that would work from a plumbing perspective was in the same closet as the sump pump (that is also where the main water line comes into the house as well). The plumber advised that this particular water softener would be fine with discharging into the sump pump and that he did the same thing with his house.

        The pump already drains into a dry creek, so I'm not worried about the grass being killed. What worries me is hearing that the discharging can damage my actual sump pump. Did the plumber really give me good information stating that THIS particular softener is fine to drain into the sump pump, or did he just cause me a lot of furture damage down ther road?

        Thank you all in advance for the help with this!

        John

        P.S. - I've been trying to search as much as possible about this specific softener/water purifier in regards to the discharge amount/contents, but have had little to no luck.
         
        Posts: 3 | Registered: Jan 17, 2013Reply With QuoteReport This Post
        posted Hide Post
        Does this water softener use salt? If so, you're discharging salt water into the dry creek bed.

        Here is a paper from Rhode Island on the subject. You might search for something similar from your state or local government. In RI at least it isn't illegal to dump it on the ground, though they prefer a dry well. Link is a pdf.

        http://www.dem.ri.gov/programs...ll/pdfs/backwash.pdf


        General Disclaimer

        Any advice given here is general in nature and is not necessarily valid for your given area. If in doubt check with your local codes enforcement department for what is required when doing electrical, plumbing or structural work on your house. Permits may or may not be required in your area and home owners may not be able to DIY some tasks. I have no way of knowing if you have the skills needed to complete the tasks you are asking about, when in doubt seek professional assistance.

        My advice may be worth exactly what you pay me for it. :-) For the record I did not stay in a Holiday Inn Express last night.
         
        Posts: 239 | Location: Cary, NC | Registered: Aug 17, 2006Reply With QuoteReport This Post
        posted Hide Post
        The softener does use salt. I should also mention that when I say dry creek, it is a bed of rock that we built on our property. It is not dumping into common ground or anything. We just put the rock there for general runoff from the sump pump. I'm more worried about the salt dumping into the pump. On one hand I have a plumber saying its no problem. On the other hand I've read that it's no big deal...and others saying its not good at all.

        This message has been edited. Last edited by: JohnG83,
         
        Posts: 3 | Registered: Jan 17, 2013Reply With QuoteReport This Post
        posted Hide Post
        While RI apparently allows it, it is not the best practice. Your state may have different regulations than RI so you might want to check with them to make sure you're not running afoul of their clean water requirements. The link I provided has a lot of good information on the subject and the problems with different ways of disposing of the water.

        Are you on a well or city water? Do you have sanitary sewers or your own septic tank?


        General Disclaimer

        Any advice given here is general in nature and is not necessarily valid for your given area. If in doubt check with your local codes enforcement department for what is required when doing electrical, plumbing or structural work on your house. Permits may or may not be required in your area and home owners may not be able to DIY some tasks. I have no way of knowing if you have the skills needed to complete the tasks you are asking about, when in doubt seek professional assistance.

        My advice may be worth exactly what you pay me for it. :-) For the record I did not stay in a Holiday Inn Express last night.
         
        Posts: 239 | Location: Cary, NC | Registered: Aug 17, 2006Reply With QuoteReport This Post
        posted Hide Post
        Thanks for the good info thus far. I'll look into my state regulations. I am on a city sewer system, but the plumber couldn't fit the softener close to my center drain in the house due to the way the basement was finished. I looked at the manual and it stated that using a sump is fine. I'm just worried about causing damage to the pump.
         
        Posts: 3 | Registered: Jan 17, 2013Reply With QuoteReport This Post
          Powered by Social Strata  
         

            DIY Message Boards  Hop To Forum Categories  Home Improvement  Hop To Forums  General Home Improvement    Water Softener Discharging into a Sump Pump

        © Scripps Networks 2009

        Advertisement

        Posting Guidelines

        • Please be sure posts are category appropriate.
        • No off-topic or off-color postings.
        • Postings may be deleted at the discretion of DIY moderators.
        • No advertising is allowed.
        • Be nice. No name calling, personal attacks or flaming.
        • Certain words will trigger moderation of the post. These words mostly cover political or religious topics, which are OFF the topics covered by DIY.

        Full Guidelines

        For general message board help, click the tab labeled "Tools," and choose "Help" from the dropdown menu.